Installation Instructions for ROLA Door Frame Fit Kit System

Part Number:

• R5014

Vehicle Compatibility:

• Toyota Tacoma, 4-door Double Cab (2005+)

Tools Required:

• Torque Wrench (Included)
• Tape Measure
• Lubricant for Locks (Recommended)
• Soft Cloth for Cleaning

Components Included:

• (4) End Supports
• (2) Cross Bars
• (4) Buffer Strips
• (4) Door Frame Straps
• (4) Rubber Gasket Pads
• (1) Installation Manual

Safety Warnings:

• Maximum Load Limit: 110 lbs (50 kg), including cross bars, accessories, and cargo.
• Always ensure loads are tied down securely using non-stretch straps.
• Check all bolts, straps, and locks before each trip for tightness and signs of wear.
• Remove cross bars when not in use or before entering automatic car washes.
• Do not exceed the vehicle's roof load limit as specified in the owner’s manual.

Installation Steps:

Step 1: Prepare for Installation

1. Clean the vehicle roof and ensure all components are free from debris or damage.
2. Measure and mark the correct cross bar positions based on the vehicle specifications:
   • Front Bar Position: 11.8 inches (300 mm)
   • Rear Bar Position: 27.5 inches (700 mm)

Step 2: Assemble Cross Bars

1. Slide the outer under-cover strips out of the cross bars.
2. Insert the position slider tabs into the rails and align them with the X and Y measurement scales provided for your vehicle.
3. Attach the end supports by sliding them into the rails until they meet the position slider tabs.

Step 3: Install Door Frame Straps and Gasket Pads

1. Open the end support covers and install the door frame straps.
2. Attach the gasket pads to the end supports, ensuring they align with the roof edge.

Step 4: Position and Secure Cross Bars

1. Place the cross bars onto the roof at the measured positions.
2. Adjust the end supports so they align with the vehicle’s door frame.
3. Tighten the tensioning bolts alternately using the torque wrench until the 4Nm marking aligns.
4. Secure the door frame straps firmly against the vehicle frame.

Step 5: Install Buffer Strips

1. Measure and cut the buffer strips to fit the length of the cross bars.
2. Insert the buffer strips into the cross bar slots, leaving no gaps.

Step 6: Finalize Installation

1. Test the installation by gently pushing and pulling the cross bars to ensure they are secure.
2. Close and lock the end support covers using the quarter-turn plugs.

Maintenance Tips:

• Periodically check and re-tighten all bolts and straps.
• Lubricate locks and bolts to prevent corrosion.
• Remove cross bars during winter or prolonged periods of non-use.
• Inspect for wear and replace any damaged components.

Important Notes:

• Long items such as kayaks or construction materials must be tied down to both the front and rear bumpers.
• Be mindful of additional height clearance needed when transporting upright loads.
• The vehicle’s handling and braking characteristics may change with loads on the roof.

Installation Instructions for Door Frame Fit Kit System

Part Number:

• R5014

Vehicle Compatibility:

• Toyota Tacoma, 4-door Double Cab (2005+)

Tools Required:

• Torque Wrench (Included)
• Tape Measure
• Lubricant for Locks (Recommended)
• Soft Cloth for Cleaning

Components Included:

• (4) End Supports
• (2) Cross Bars
• (4) Buffer Strips
• (4) Door Frame Straps
• (4) Rubber Gasket Pads
• (1) Installation Manual

Safety Warnings:

• Maximum Load Limit: 110 lbs (50 kg), including cross bars, accessories, and cargo.
• Always ensure loads are tied down securely using non-stretch straps.
• Check all bolts, straps, and locks before each trip for tightness and signs of wear.
• Remove cross bars when not in use or before entering automatic car washes.
• Do not exceed the vehicle's roof load limit as specified in the owner’s manual.

Installation Steps:

Step 1: Prepare for Installation

1. Clean the vehicle roof and ensure all components are free from debris or damage.
2. Measure and mark the correct cross bar positions based on the vehicle specifications:
   • Front Bar Position: 11.8 inches (300 mm)
   • Rear Bar Position: 27.5 inches (700 mm)

Step 2: Assemble Cross Bars

1. Slide the outer under-cover strips out of the cross bars.
2. Insert the position slider tabs into the rails and align them with the X and Y measurement scales provided for your vehicle.
3. Attach the end supports by sliding them into the rails until they meet the position slider tabs.

Step 3: Install Door Frame Straps and Gasket Pads

1. Open the end support covers and install the door frame straps.
2. Attach the gasket pads to the end supports, ensuring they align with the roof edge.

Step 4: Position and Secure Cross Bars

1. Place the cross bars onto the roof at the measured positions.
2. Adjust the end supports so they align with the vehicle’s door frame.
3. Tighten the tensioning bolts alternately using the torque wrench until the 4Nm marking aligns.
4. Secure the door frame straps firmly against the vehicle frame.

Step 5: Install Buffer Strips

1. Measure and cut the buffer strips to fit the length of the cross bars.
2. Insert the buffer strips into the cross bar slots, leaving no gaps.

Step 6: Finalize Installation

1. Test the installation by gently pushing and pulling the cross bars to ensure they are secure.
2. Close and lock the end support covers using the quarter-turn plugs.

Maintenance Tips:

• Periodically check and re-tighten all bolts and straps.
• Lubricate locks and bolts to prevent corrosion.
• Remove cross bars during winter or prolonged periods of non-use.
• Inspect for wear and replace any damaged components.

Important Notes:

• Long items such as kayaks or construction materials must be tied down to both the front and rear bumpers.
• Be mindful of additional height clearance needed when transporting upright loads.
• The vehicle’s handling and braking characteristics may change with loads on the roof.

Attention:

This is a summary of the installation procedure. For complete installation instructions, including diagrams and detailed information from the manufacturer, please download the full installation PDF.

Warranty Information:

For complete warranty instructions, please download the full installation PDF.

Technical Support:

For technical support and assistance, our team of experts is available to help. You can reach our tech support by visiting www.trailerjacks.com or calling 877-869-6690.