Installation Instructions for Dodge/Ram Pickup Trucks (Various Models)

Part Numbers:

• N75073

Tools Required:

• Wrenches (sizes not specified)
• Torque Wrench
• Ratchet

Step-by-Step Instructions:

1. Prepare Vehicle:

   • Clean the mounting areas on the frame rails to ensure proper contact with the hitch and fasteners.

2. Position Hitch:

   • Place the hitch on the frame rails, aligning the attachment holes with existing frame holes.

3. Insert Fasteners:

   • Install the carriage bolts, flat washers, and nuts as per the provided diagram.
   • Use the pull wire method if applicable to guide bolts through the frame.

4. Align and Center Hitch:

   • Adjust the hitch to ensure it is centered and aligned with the frame rails.

5. Tighten Fasteners:

   • Torque all fasteners to the specified torque values.

Torque Specifications:

• Refer to standard torque settings for the bolt grades included in the hardware kit.

Hardware List:

• (Details of hardware components, e.g., bolt sizes and quantities, to be added from the provided diagram or list in the manual.)

Safety Notes:

• Regularly inspect the hitch to ensure all fasteners and the ball are securely tightened.
• Replace any damaged hitch or ball immediately.
• Plug any holes in the frame or body panels if the hitch is removed to prevent water or exhaust fumes from entering.
• Always wear safety glasses and observe proper safety precautions when working beneath the vehicle.
• Do not cut access or attachment holes with a torch.

Specifications:

• Weight Carrying (Ball Mount):
  • Max Gross Trailer Weight: (Details to be added from manual)
  • Max Tongue Weight: (Details to be added from manual)

Additional Notes:

• This product complies with SAE J684 safety standards.
• Follow the provided diagrams closely for correct installation.

Installation Instructions for Pickup Trucks (Various Models)

Part Numbers:

• N75073

Tools Required:

• Wrenches (sizes not specified)
• Torque Wrench
• Ratchet

Step-by-Step Instructions:

1. Prepare Vehicle:

   • Clean the mounting areas on the frame rails to ensure proper contact with the hitch and fasteners.

2. Position Hitch:

   • Place the hitch on the frame rails, aligning the attachment holes with existing frame holes.

3. Insert Fasteners:

   • Install the carriage bolts, flat washers, and nuts as per the provided diagram.
   • Use the pull wire method if applicable to guide bolts through the frame.

4. Align and Center Hitch:

   • Adjust the hitch to ensure it is centered and aligned with the frame rails.

5. Tighten Fasteners:

   • Torque all fasteners to the specified torque values.

Torque Specifications:

• Refer to standard torque settings for the bolt grades included in the hardware kit.

Hardware List:

• (Details of hardware components, e.g., bolt sizes and quantities, to be added from the provided diagram or list in the manual.)

Safety Notes:

• Regularly inspect the hitch to ensure all fasteners and the ball are securely tightened.
• Replace any damaged hitch or ball immediately.
• Plug any holes in the frame or body panels if the hitch is removed to prevent water or exhaust fumes from entering.
• Always wear safety glasses and observe proper safety precautions when working beneath the vehicle.
• Do not cut access or attachment holes with a torch.

Specifications:

• Weight Carrying (Ball Mount):
  • Max Gross Trailer Weight: (Details to be added from manual)
  • Max Tongue Weight: (Details to be added from manual)

Additional Notes:

• This product complies with SAE J684 safety standards.
• Follow the provided diagrams closely for correct installation.

Technical Support:

For technical support and assistance, our team of experts is available to help. You can reach our tech support by visiting www.trailerjacks.com or calling 877-869-6690.

Attention:

This is a summary of the installation procedure. For complete installation instructions, including diagrams and detailed information from the manufacturer, please download the full installation PDF.

Warranty:

The product comes with a standard warranty. For complete warranty instructions, please download the full installation PDF.

Installation Instructions for T-Connector Adapter

Part Numbers:

• 118329

Wiring Access Location:

• Near the rear frame of the vehicle.

Tools Required:

• Tie straps (provided in the kit).

Step-by-Step Instructions:

1. Locate the vehicle’s taillight wiring harness near the rear of the frame.

   • The harness will have connection points on both sides with connectors matching the ends of the T-Connector adapter.

2. Separate the harness connectors on the left (driver’s) side.

   • Note: Be careful not to break the locking tabs.
   • Ensure that the mating surfaces of the connectors are free of dirt and clean them if necessary.

3. Insert the T-Connector adapter with the yellow wire between the harness connectors and lock into place.

   • Verify that the connectors are fully inserted with locking tabs secure.

4. Repeat steps 2 and 3 on the right (passenger’s) side, using the T-Connector with the green wire.

5. Route the T-Connector harness to the center of the vehicle.

   • Secure the wire to the vehicle crossmember using the provided tie straps.

6. Test the installation with a test light or trailer.

   • Specifications:
     • This unit is rated for 7.5 amps per circuit.

Hardware List:

• T-Connector adapter.
• Tie straps.

Safety Notes:

• Handle all connectors with care to avoid damage.
• Ensure all connections are clean and securely fastened.
• Test the installation after completing all steps to verify functionality.

Manufacturer Notes:

• Follow all warnings and instructions provided with the product.
• Use a test light or trailer to confirm proper installation.

Installation Instructions for T-Connector Adapter

Part Numbers:

• 118329

Wiring Access Location:

• Near the rear frame of the vehicle.

Tools Required:

• Tie straps (provided in the kit)

Step-by-Step Instructions:

1. Locate the Vehicle’s Taillight Wiring Harness:

   • Locate the vehicle’s taillight wiring harness near the rear of the frame.
   • The harness will have connection points on both sides with connectors matching the ends of the T-Connector adapter.

2. Separate the Harness Connectors on the Left (Driver’s) Side:

   • Note: Be careful not to break the locking tabs.
   • Ensure that the mating surfaces of the connectors are free of dirt and clean them if necessary.

3. Insert the T-Connector Adapter with the Yellow Wire:

   • Insert the T-Connector adapter with the yellow wire between the harness connectors and lock it into place.
   • Verify that the connectors are fully inserted with locking tabs secure.

4. Repeat for the Right (Passenger’s) Side:

   • Repeat steps 2 and 3 on the right (passenger’s) side, using the T-Connector with the green wire.

5. Route the T-Connector Harness:

   • Route the T-Connector harness to the center of the vehicle.
   • Secure the wire to the vehicle crossmember using the provided tie straps.

6. Test the Installation:

   • Test the installation with a test light or trailer to ensure all connections function properly.

Specifications:

• Maximum Current Rating: 7.5 amps per circuit

Hardware List:

• T-Connector adapter
• Tie straps

Safety Notes:

• Handle all connectors with care to avoid damage.
• Ensure all connections are clean and securely fastened.
• Test the installation after completing all steps to verify functionality.

Additional Information:

Attention: This is a summary of the installation procedure. For complete installation instructions, including diagrams and detailed information from the manufacturer, please download the full installation PDF.

Technical Support:
For technical support and assistance, our team of experts is available to help. You can reach our tech support by visiting www.trailerjacks.com or calling 877-869-6690.

Warranty Information:
For complete warranty instructions, please download the full installation PDF.

Note: Follow all warnings and instructions provided with the product. Use a test light or trailer to confirm proper installation.