Installation Instructions for T-One® T-Connector (Product Number: 22111) ### Part Numbers: - 22111 - 22111-037 (Rev. A, 6/25/2014) ### Equipment Required: - Trim Panel Remover - 10mm Socket & Ratchet or 10mm Wrench - 1/4” Socket - Wire Cutters - Test-probe ### Hardware List: - (1) T-One® T-Connector Harness - (1) 7-Way Connector (Car End) - (1) 10 Amp Fuse (Provided) - (2) 30 Amp Fuses (Provided) - Cable Ties (Provided) ### Tools Needed: - (2) 1-1/8” Wrenches or Large Adjustable Wrenches ### Step-by-Step Instructions: 1. Locate the Towplug: - Locate the vehicle’s towplug under the vehicle on the passenger side near the right side of the muffler. - Reach up into the opening to locate the grey towplug. Disconnect the protective cover and discard. - Connect the towplug harness to the mating harness, ensuring that the connectors are clean and fully inserted with locking tabs in place. 2. Route 7-Way Connector: - Route the 7-Way connector to the center of the vehicle. - Mount the 7-Way end in an accessible location using a bracket or electrical box (not included). Note: See the 7-Way diagram for wire locations. 3. Remove Taillight Housing Assemblies: - Open the rear door and remove both taillight housing assemblies by removing the two bolts for each light. - Carefully pry the housing assemblies away from the vehicle, ensuring not to break the alignment tabs. 4. Route Harness and Connect Green Wire: - Route the harness containing the green wire underneath the vehicle, up through the opening between the vehicle bumper and body, and into the passenger side taillight pocket. - Insert the T-Connector end with the green wire into the vehicle’s taillight connector and lock it into place. Warning: Be careful to avoid hot pipes, heat shields, the fuel tank, or any points that could pinch or break the wire. 5. Repeat for Driver’s Side: - Repeat the process for the driver's side using the T-Connector with the yellow wire. 6. Insert Fuses into Vehicle’s Fuse Box: - Under the vehicle hood, locate the vehicle’s fuse box. - Insert the provided 10 Amp fuse into position D1. - Insert the provided 30 Amp fuses into positions D2 and D3. Warning: All connections must be complete for the T-Connector to function properly. Test and verify the installation with a test light or trailer. 7. Reinstall Taillight Housing Assemblies: - Reinstall the taillight housing assemblies, positioning the vehicle wiring harness between the housing and the vehicle body. - Secure the T-connector harness with the provided cable ties to prevent damage or rattling, and avoid areas that could cut or pinch the wires. Warning: Overloading the circuit can cause fires. Do not exceed the lower of the vehicle manufacturer’s rating or the following: - Max. stop/turn light: 10 amps - Max. tail lights: 10 amps - Max. backup: 10 amps - Max. power circuit: 30 amps - Max. trailer brakes: 3 axles/6 brakes (20 amps) Check the vehicle’s owner’s manual and the instruction sheet for additional information. ### Safety Notes: - Warning: Overloading the circuit may cause fires. Always adhere to the manufacturer's electrical specifications. - Warning: Towing multiple trailers is illegal in many jurisdictions and can cause severe instability, loss of control, and accidents. - Warning: Ensure all connections are secure and test the system after installation. ### Warranty Information: - 1-Year Limited Warranty: This product is covered for defects in material and workmanship for one year, excluding normal wear and tear. - Warranty Limitations: The warranty does not cover misuse, neglect, improper installation, or modifications. ### Manufacturer Notes: - Ensure proper routing of wires to avoid damage from heat sources or pinch points. - Verify all connections and fuse installation to ensure proper function before use.

Installation Instructions for T-One® T-Connector

Part Numbers:

• 22111
• 22111-037 (Rev. A, 6/25/2014)

Equipment Required:

• Trim Panel Remover
• 10mm Socket & Ratchet or 10mm Wrench
• 1/4” Socket
• Wire Cutters
• Test-probe

Hardware List:

• (1) T-One® T-Connector Harness
• (1) 7-Way Connector (Car End)
• (1) 10 Amp Fuse (Provided)
• (2) 30 Amp Fuses (Provided)
• Cable Ties (Provided)

Tools Needed:

• (2) 1-1/8” Wrenches or Large Adjustable Wrenches

Step-by-Step Instructions:

1. Locate the Towplug:

   • Locate the vehicle’s towplug under the vehicle on the passenger side near the right side of the muffler.
   • Reach up into the opening to locate the grey towplug. Disconnect the protective cover and discard.
   • Connect the towplug harness to the mating harness, ensuring that the connectors are clean and fully inserted with locking tabs in place.

2. Route 7-Way Connector:

   • Route the 7-Way connector to the center of the vehicle.
   • Mount the 7-Way end in an accessible location using a bracket or electrical box (not included).
     Note: See the 7-Way diagram for wire locations.

3. Remove Taillight Housing Assemblies:

   • Open the rear door and remove both taillight housing assemblies by removing the two bolts for each light.
   • Carefully pry the housing assemblies away from the vehicle, ensuring not to break the alignment tabs.

4. Route Harness and Connect Green Wire:

   • Route the harness containing the green wire underneath the vehicle, up through the opening between the vehicle bumper and body, and into the passenger side taillight pocket.
   • Insert the T-Connector end with the green wire into the vehicle’s taillight connector and lock it into place.
     Warning: Be careful to avoid hot pipes, heat shields, the fuel tank, or any points that could pinch or break the wire.

5. Repeat for Driver’s Side:

   • Repeat the process for the driver's side using the T-Connector with the yellow wire.

6. Insert Fuses into Vehicle’s Fuse Box:

   • Under the vehicle hood, locate the vehicle’s fuse box.
   • Insert the provided 10 Amp fuse into position D1.
   • Insert the provided 30 Amp fuses into positions D2 and D3.
     Warning: All connections must be complete for the T-Connector to function properly. Test and verify the installation with a test light or trailer.

7. Reinstall Taillight Housing Assemblies:

   • Reinstall the taillight housing assemblies, positioning the vehicle wiring harness between the housing and the vehicle body.
   • Secure the T-connector harness with the provided cable ties to prevent damage or rattling, and avoid areas that could cut or pinch the wires.
     Warning: Overloading the circuit can cause fires. Do not exceed the lower of the vehicle manufacturer’s rating or the following:
     • Max. stop/turn light: 10 amps
     • Max. tail lights: 10 amps
     • Max. backup: 10 amps
     • Max. power circuit: 30 amps
     • Max. trailer brakes: 3 axles/6 brakes (20 amps)
       Check the vehicle’s owner’s manual and the instruction sheet for additional information.

Safety Notes:

• Warning: Overloading the circuit may cause fires. Always adhere to the manufacturer's electrical specifications.
• Warning: Towing multiple trailers is illegal in many jurisdictions and can cause severe instability, loss of control, and accidents.
• Warning: Ensure all connections are secure and test the system after installation.

Warranty Information:

• 1-Year Limited Warranty: This product is covered for defects in material and workmanship for one year, excluding normal wear and tear.
• Warranty Limitations: The warranty does not cover misuse, neglect, improper installation, or modifications.

Manufacturer Notes:

• Ensure proper routing of wires to avoid damage from heat sources or pinch points.
• Verify all connections and fuse installation to ensure proper function before use.

Warranty Information:

For complete warranty instructions, please download the full installation PDF.

Technical Support:

For technical support and assistance, our team of experts is available to help. You can reach our tech support by visiting www.trailerjacks.com or calling 877-869-6690.

Attention:

This is a summary of the installation procedure. For complete installation instructions, including diagrams and detailed information from the manufacturer, please download the full installation PDF.

Revision:

22111-037 Rev. A 6/25/2014